Plastic Mold Cleaner
Introducing iD Eco-Pro 360, a water-based, eco-friendly plastic mold cleaner that effectively removes rust and offers long-term rust protection, all while being non-aerosol, non-flammable, no VOCs, and ready-to-use.
Benefits & Features
- Safely removes rust, mineral, and limescale buildup
- Provides a protective nano-coating for rust prevention
- Works on all metal surfaces (without etching)
- Can be reused with proper filtration
- Reduces labor, time, and cost
- Proudly made in the USA
- EPA Tested & Verified Green Product
- Available in 16 oz. Spray Bottle, 1 Gallon Container, 5 Gallon Container, 55 Gallon Drum
— What They're Saying —
“Many of our donated course molds arrive with water lines that are plugged with rust, mineral deposits and just general crude. The Eco Pro makes quick work of these no matter the level of contamination. Our course attendees that purchase the Eco Pro tell us that once set-up with the appropriate quick disconnect fittings, keeping the water lines clean is fast and much more cost effective than other larger, more expensive units on the market. We highly recommend the Eco Pro as a “must have” shop tool that will keep your cooling lines clean and your molds running better!”
Steve Johnson, MoldTrax
iD Eco-Pro 360 System
Our iD Eco-Pro System is comprised of the Eco-Pro cart (two sizes) and was created for using the Eco-Pro 360 chemical. iD Eco-Pro 360 System is a Preventative Maintenance Cleaning System with a pump and filter combination unit. It removes, protects, and helps prevent rust within the Cooling Passages, Heat Exchangers, Water Lines, TCUs/Thermolators, Chill Rolls, Chill Rails, Feed Sections, Tools, and more. The built-in filter function allows the Eco-Pro 360 solution to remain at peak performance for optimal reusability.
- Acid resistant components – designed for the Eco-Pro 360 chemicalRuns off your compressed air – no electrical needed
- Safe operation – independently ceases if needed
- Filters out contaminants, so Eco-Pro 360 can be reused until it is gone!
- Safe operation- independently ceases when a blockage is present, avoiding downstream ruptures
Eco-Pro 360 FAQ
Find answers to some of the most common questions we receive regarding our Eco-Pro 360 product. If you have additional questions just reach out!
iD Eco-Pro 360 can be applied by brushing, spraying, dipping, or wiping. Only a very thin coating is required, so use conservatively. After one minute of application, wipe or blow off excess chemical. If excess chemical is left on the surface, it will become a residue (chalky white), which can have an effect on bonding and corrosion resistance. This chalk white residue can be removed by another application of Eco-Pro 360, or by using a warm, damp cloth.
It’s recommended to use the Eco-Pro 360 cart, which was designed specifically for the Eco-Pro 360 chemical. By pumping iD Eco-Pro 360 through your system, it will remove the rust, limescale, and calcium buildup. The built-in filter allows individuals to continue using iD Eco-Pro 360. Flushing times vary based on buildup. Initial cleanings take the longest, but future PMs will have significantly shortened flushing times.
If your cooling passages are aluminum, have brass inserts, or the chemical comes into any contact with rubber seals (closed molds), you will need to backflush with water (can use the cart for this step, too). Most heat exchangers have copper lines in them – it is a requirement to backflush this metal with water.
iD Eco-Pro 360 can last over 10 years when stored indoors in a cool and dry place (no direct sunlight).
Simply dilute the chemical with a large amount of water.
Over time, this material will cause swelling and dry rot of rubber compounds – it is recommended to break material down with water (time varies based on compound – most take longer than a month for effects to occur).
Amazing iD Transformation
Find answers to some of the most common questions we receive regarding our Eco-Pro 360 product. If you have additional questions just reach out!
Eco-Pro 360 Videos
